Quality Inspection for Oobm Network - Mylinking™ Network Tap ML-TAP-2810 – Mylinking
Quality Inspection for Oobm Network - Mylinking™ Network Tap ML-TAP-2810 – Mylinking Detail:
1- Overviews
- A full visual control of Data Acquisition device(4*10GE SFP+ plus 24*GE SFP ports)
- A full Data Scheduling Management of nework traffic capture and monitoring device(duplex Rx/Tx processing)
- A full packet pre-processing and re-distribution device(bidirectional bandwidth 64Gbps)
- Supported traffic collection & reception of link data from different network element locations
- Supported traffic collection & reception of link data from different switch routing nodes
- Supported raw packet captured, identified, analyzed, statistically summarized and marked
- Supported packet filtering matches, including policy filtering based on quintuple (source IP address, destination IP address, source port, destination port, and protocol number), packet characteristics, and deep identification of packet content
- Supported raw packet output for monitoring equipment of Data Packet Analysis, Protocol Analysis, Signaling Analysis, Security Analysis, Risk Management and other traffic reqirement.
ML-TAP-2810
2- System Block Diagram
3- Operating Principle
The Network Traffic Tap embedded traffic guidance function, which is mainly coordinated by the built-in TCAM traffic identification policy engine, traffic control guidance engine, port media transceiver module (MAC+PHY), and high-speed backplane switch bus. The port media transceiver module collects the traffic and enters the traffic identification matching engine to perform traffic identification matching. The identification matching engine performs high-speed hardware parallel matching based on the TCAM three-state content addressing memory, which can complete high-speed traffic identification of line speed traffic. After traffic identification, the traffic will enter the high-speed switching bus for traffic forwarding, replication, aggregation, or shunting. The traffic control guide engine can accurately control the traffic output interface of each type of traffic identification frame.
4- Intelligent Traffic Processing Abilities
6- Specifications
|
Mylinking™ Network Tap NPB/TAP Functional Parameters |
||
| Network Interface | GE ports |
24*GE SFP slots |
| 10GE ports |
4*10GE SFP+ slots |
|
| Deployment mode | SPAN monitoring input |
support |
| In-line mode |
support |
|
| Total QTYs interface |
28 |
|
| Traffic replication / aggregation / distribution |
support |
|
| Link QTYs supporting Mirror replication / aggregation |
1 -> N link traffic replication (N <28) N-> 1 link traffic aggregation (N <28) G Group(M-> N Link) traffic replication and aggregation [G * (M + N) <28] |
|
|
Functions |
Distribution based on traffic identification |
support |
| Distribution based on IP / protocol / port Five tuple traffic identification |
support |
|
| Distribution strategy based on protocol header the key labeled traffic identifies |
support |
|
| Strategic distribution based on deep message content identification |
support |
|
| Support Ethernet encapsulation independence |
support |
|
| CONSOLE Network Management |
support |
|
| IP/WEB Network Management |
support |
|
| SNMP V1/V2C Network Management |
support |
|
| TELNET/SSH Network Management |
support |
|
| SYSLOG Protocol |
support |
|
| User authentication function |
Password authentication based on user name |
|
|
Electric(1+1 Redundant Power System-RPS) |
Rated supply voltage |
AC110-240V/DC-48V [Optional] |
| Rated power frequency |
AC-50HZ |
|
| Rated input current |
AC-3A / DC-10A |
|
| Rated power function |
150W(2401: 100W ) |
|
|
Environment |
Operating Temperature |
0－50℃ |
| Storage Temperature |
-20-70℃ |
|
| Operating Humidity |
10%-95%, Non-condensing |
|
|
User Configuration |
Console Configuration |
RS232 Interface, 9600,8,N,1 |
| Password authentication |
support |
|
|
Rack Height |
Rack space (U) |
1U 460mm*45mm*440mm |
7- Order Information
ML-TAP-2401 mylinking™ Network Tap 24*GE SFP ports
ML-TAP-1410 mylinking™ Network Tap 12*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2610 mylinking™ Network Tap 24*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2810 mylinking™ Network Tap 24*GE SFP ports plus 4*10GE SFP+ ports
Product detail pictures:
Related Product Guide:
We always continually offer you by far the most conscientious customer service, and the widest variety of designs and styles with finest materials. These attempts include the availability of customized designs with speed and dispatch for Quality Inspection for Oobm Network - Mylinking™ Network Tap ML-TAP-2810 – Mylinking , The product will supply to all over the world, such as: Benin, India, Florida, Insisting over the high-quality generation line management and prospects guide provider, we've made our resolution to offer our shoppers using the initially stage purchasing and soon after provider working experience. Preserving the prevailing helpful relations with our prospects, we even now innovate our product lists the many time to meet up with the brand new wants and stick to the latest trend of this business in Ahmedabad. We're ready to facial area the difficulties and make the transform to grasp many of the possibilities in international trade.
By Ellen from Toronto - 2018.06.03 10:17
This company conforms to the market requirement and joins in the market competition by its high quality product, this is an enterprise that have Chinese spirit.
By Mario from Qatar - 2017.08.18 18:38
