Mylinking™ Network Tap ML-TAP-2810

24*GE SFP plus 4*10GE SFP+, Max 64Gbps

Short Description:

Mylinking™ Network Tap of ML-TAP-2810 has up to 64Gbps processing capacity optical splitting or  mirroring span access. It supports a maximum of 4 * 10 Gigabit SFP+ slots (compatible with 1 Gigabit) and 24 * 1 gigabit SFP slots, flexible support 10G and 1G single/multi-mode optical modules and 10 gigabit and 1 Gigabit electrical modules. Supports Gigabit and 10GE Ethernet link data capture strategy, supports network traffic data packet filtering: based on quintuple (source IP, destination IP, source port, destination port, protocol), packet characteristics, deep packet content identification strategy shunt elements such as flexible combination of shunt, traffic analysis, flow filtering, Intrusion Detection System(ISD) and other application designed for the equipment level solutions.


Product Detail

Product Tags

1- Overviews

  • A full visual control of Data Acquisition device(4*10GE SFP+ plus 24*GE SFP ports)
  • A full Data Scheduling Management of nework traffic capture and monitoring device(duplex Rx/Tx processing)
  • A full packet pre-processing and re-distribution device(bidirectional bandwidth 64Gbps)
  • Supported traffic collection & reception of link data from different network element locations
  • Supported traffic collection & reception of link data from different switch routing nodes
  • Supported raw packet captured, identified, analyzed, statistically summarized and marked
  • Supported packet filtering matches, including policy filtering based on quintuple (source IP address, destination IP address, source port, destination port, and protocol number), packet characteristics, and deep identification of packet content
  • Supported raw packet output for monitoring equipment of Data Packet Analysis, Protocol Analysis, Signaling Analysis, Security Analysis, Risk Management and other traffic reqirement.
product-description1

ML-TAP-2810

2- System Block Diagram

product-description2

3- Operating Principle

product-description3

The Network Traffic Tap embedded traffic guidance function, which is mainly coordinated by the built-in TCAM traffic identification policy engine, traffic control guidance engine, port media transceiver module (MAC+PHY), and high-speed backplane switch bus. The port media transceiver module collects the traffic and enters the traffic identification matching engine to perform traffic identification matching. The identification matching engine performs high-speed hardware parallel matching based on the TCAM three-state content addressing memory, which can complete high-speed traffic identification of line speed traffic. After traffic identification, the traffic will enter the high-speed switching bus for traffic forwarding, replication, aggregation, or shunting. The traffic control guide engine can accurately control the traffic output interface of each type of traffic identification frame.

4- Intelligent Traffic Processing Abilities

product description

ASIC Chip Plus TCAM CPU
64Gbps intelligent traffic processing capabilities

product-description1

10GE Acquisition
10GE 4 ports, Max 4*10GE plus 24*GE ports Rx/Tx duplex processing, up to 64Gbps Traffic Data Transceiver at same time, for network Data Acquisition, simple Pre-processing

product description (2)

Data Replication
Packet replicated from 1 port to multiple N ports, or multiple N ports aggregated, then replicated to multiple M ports

product description (3)

Data Aggregation 
Packet replicated from 1 port to multiple N ports, or multiple N ports aggregated, then replicated to multiple M ports

product description (4)

Data Distribution 
Classified the incoming metdata accurately and discarded or forwarded different data services to multiple interface outputs according to user’s predefined rules.

product description (5)

Packet Filtering
Supported L2-L7 packet filtering matching, such as SMAC, DMAC, SIP, DIP, Sport, Dport, TTL, SYN, ACK, FIN, Ethernet type field and value, IP protocol number, TOS, etc. also supported flexible combination of up to 2000 filtering rules.

product description

Load Balancing
Supported load balance Hash algorithm and session-based weight sharing algorithm according to L2-L7 layer characteristics to ensure that the port output traffic dynamic of load balancing

product description (6)

UDF Match
Supported the matching of any key field in the first 128 bytes of a packet. Customized the Offset Value and Key Field Length and Content, and determining the traffic output policy according to the user configuration

product description (7)

VLAN Tagged

product description (8)

VLAN Untagged

product description (9)

VLAN Replaced

Supported the matching of any key field in the first 128 bytes of a packet. The user can customize the offset value and key field length and content, and determine the traffic output policy according to the user configuration.

product description (10)

MAC Address Replacement
Supported the replacement of the destination MAC address in the original data packet, which can be implemented according to the user's configuration

product description (11)

3G/4G Mobile Protocol Identification/Classification
Supported to identify mobile network elements such as (Gb, Gn, IuPS, S1-MME, S1-U, X2-U, S3, S4, S5, S6a, S11, etc. interface). You can implement traffic output policies based on features such as GTPV1-C, GTPV1-U, GTPV2-C, SCTP, and S1-AP based on user configurations.

product description (12)

Ports Healthy Detection
Supported real-time detection of the service process health of the back-end monitoring and analysis equipment connected to different output ports. When the service process fails, the faulty device is automatically removed. After the faulty device is recovered, the system automatically returns to the load balancing group to ensure the reliability of multi-port load balancing.

product description (13)

VLAN, MPLS Untagged
Supported the VLAN, MPLS header stripping in the original data packet as output.

product description (14)

Tunneling Protocol Identify
Supported automatically identify various tunneling protocols such as GTP / GRE / PPTP / L2TP / PPPOE. According to the user configuration, the traffic output strategy can be implemented according to the inner or outer layer of the tunnel

product description (15)

Unified Control Platform
Supported mylinking™ Visibility Control Platform Access

product description (16)

1+1 Redundant Power System(RPS)
Supported 1+1 Dual Redundant Power System

5- Mylinking™ Network Tap Typical Application Structures

5.1 Mylinking™ Network Tap GE to 10GE Data Aggregation Application(as following)

product-description4

5.2  Mylinking™ Network Tap 1/10GE Data Distribution Application(as following)

product-description5

5.3 Mylinking™ Network Tap Hybrid Network Traffic Acquisition Application (as following)

product-description6

5.4 Mylinking™ Network Tap Customazition Traffic Monitoring Application(as following)

product-description7

6- Specifications

Mylinking™ Network Tap  NPB/TAP Functional Parameters

Network Interface GE ports

24*GE SFP slots

10GE ports

4*10GE SFP+ slots

Deployment mode SPAN monitoring input

support

In-line mode

support

Total QTYs interface

28

Traffic replication / aggregation / distribution

support

Link QTYs supporting Mirror replication / aggregation

1 -> N link traffic replication (N <28)

N-> 1 link traffic aggregation (N <28)

G Group(M-> N Link) traffic replication and aggregation [G * (M + N) <28]

Functions

Distribution based on traffic identification

support

Distribution based on IP / protocol / port Five tuple traffic identification

support

Distribution strategy based on protocol header the key labeled traffic identifies

support

Strategic distribution based on deep message content identification

support

Support Ethernet encapsulation independence

support

CONSOLE Network Management

support

IP/WEB Network Management

support

SNMP V1/V2C Network Management

support

TELNET/SSH Network Management

support

SYSLOG Protocol

support

User authentication function

Password authentication based on user name

Electric(1+1 Redundant Power System-RPS)

Rated supply voltage

AC110-240V/DC-48V [Optional]

Rated power frequency

AC-50HZ

Rated input current

AC-3A / DC-10A

Rated power function

150W(2401: 100W )

Environment

Operating Temperature

0-50℃

Storage Temperature

-20-70℃

Operating Humidity

10%-95%, Non-condensing

User Configuration

Console Configuration

RS232 Interface, 9600,8,N,1

Password authentication

support

Rack Height

Rack space (U)

1U 460mm*45mm*440mm

7- Order Information

ML-TAP-2401 mylinking™ Network Tap 24*GE SFP ports
ML-TAP-1410 mylinking™ Network Tap 12*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2610 mylinking™ Network Tap 24*GE SFP ports plus 2*10GE SFP+ ports
ML-TAP-2810 mylinking™ Network Tap 24*GE SFP ports plus 4*10GE SFP+ ports


  • Previous:
  • Next:

  • Write your message here and send it to us